AIRGRAVER
Hand Engraving Tools for
Engravers, Jewelers & Metal Artists

See what's new


TOOL PHOTOGRAPHS - CLICK HERE TO VIEW

Latest new websites!
       

HOME PAGE

WHAT IS HAND ENGRAVING?

NEW POSTS ON FORUM

About:
   LINDSAY AIRGRAVERS
   LINDSAY POINT
   CLASSIC AIRGRAVER
   PALMCONTROL
 

 FOR ONLINE STORE-CLICK HERE
or use menu below

46 Year
AirGraver History

AIRGRAVERS & PALMCONTROLS

GRAVER SHARPENING

GRAVER BLANKS

ENGRAVING VISES

ENGRAVING SETS

MORE ENGRAVING SETS

ACCESSORIES

MANUAL OPERATED ENGRAVERS

AIR COMPRESSORS

MICROSCOPES

COIN CARVING

BOOKS

NEW POSTS ON FORUM

ON-LINE RESOURCES

HANDCONTROL
ARITISAN
NITRO
   TESTIMONIALS
   PHIL COGGAN
   ROLAND BAPTISTE
   ANDY SHINOSKY
   ADONE POZZOBON
   DELIVERY & SERVICE
NEWS
TOOLS GALLERY
ENGRAVING GALLERY
VIDEOS
ENGRAVINGFORUM.COM

CONTACT-EMAIL

Engraving Resources
EngravingForum.com
   Free online engraving   
       books and videos

   EngravingClasses.com
   EngravingGlossary.com
   EngravingSchool.com

 

The More Versatile CLASSIC HANDPIECE

The versatile Classic is the same handpiece as its predecessor, but the new bore is easily replaceable with a removable sleeve. The Classic comes standard with a stainless piston.  A second piston (tungsten dead blow) can be purchased for additional power.  Three handpiece  tubing attachment locations for customability and comfort.  Non-slip rubber handle.  Full stroke adjustment.  Rapid 3/32" square graver change without collets. 

Lindsay gravers are made form surgical stainless steel.  No aluminum is used in the construction of the tool. 

The tool's patent pending removable bore provides for an extra air pocket in the handpiece. This pocket is ported to the rear chamber, providing the following improvements:

ü       The piston changes directions in the rear chamber gradually, resulting in less vibration, smoother cutting and less noise.
 

ü       The piston hesitates for a few microseconds in the front chamber following an impact stroke, giving the effect of what is known as a "dead blow". This is what occurs when a hammer hits an anvil and there is no recoil. The impact inertia is transferred through the anvil to the graver with no bounce. The result is less vibration, and more energy transferred to the graver. 
 

ü       The patented idle is improved. The idling handpiece can be turned down finer than prior handpieces, and, with the stainless piston, can be turned down so low that it is not felt. The tool will idle with less air (or CO2), as well as more easily maintain an idling state. Small amounts of oil from an older unfiltered air compressor do not affect the idle as much as on prior configurations.

---Click here to see a Gallery of work created with the Classic AirGraver---

 

Optional custom burl wood handle for foot pedal Classic handpiece

 

 

The Classic handpiece comes with a stainless piston.   A tungsten dead blow piston can be purchased separately.  Tungsten weights 2.5 to 3 times than  stainless and provides heavier impact power for deeper engraving, carving or hammering.  

Left: Classic handpiece with a PalmControl handle set up to run from a pocket sized  CO2 cartridge.  Click to enlarge

 

Classic Handpiece Impact speed range
Stainless piston = 2,400 through 15,000 strokes per minute.
Tungsten Dead Blow™ piston = 1,500 through 11,000 strokes per minute.

The length of stroke adjustment collar on the Classic handpiece provides a multitude of hand pieces in one tool. At any given stroke length setting,  the power is varied with air pressure from the foot control or PalmControl (.5psi to 60psi). The absence of an internal spring means uniform performance throughout the range, with no sweet spots or  non-working spots.  The full range of power and speed is consistent throughout due to the internal automatic balance of air pressure on both the impact and return strokes. The tool requires little air volume for operation. 0.05 to 0.2 CFM depending on the depth of engraving or impact operation.   This means the life of an air compressor will last longer and a smaller compressor can be used. 

The Classic handpiece includes length/speed stroke collar, rapid graver change, a Teflon bore in a 303 stainless body, and a hardened 440C stainless piston, anvil, and nose.  No collects required for rapid graver change.  Also included are three high speed steel 3/32" square graver blanks, a leather handpiece pouch, extra screws, wrench and owner's manual. Requires 60psi regulated compressed air from an air compressor. 

Classic handpiece with Foot control, idle adjust and dual regulators  $1369
Includes stainless piston and $125 tungsten piston
add_to_cart.gif
Classic handpiece with PalmControl $2690 add_to_cart.gif
Tungsten Dead Blow Piston $125 add_to_cart.gif
view_cart.gif

"DITTO" to what has been said. I am enjoying the AirGraver more each day. It seems like I have been using the tool all my engraving life.
Sam Welch                                                                    Additional Feedback

AirGraver® Patent & Trademark Information
Warranty & Voiding Policies

Translate Site to Language
Arabic Japanese
Chinese Korean
French Portuguese
German Russian
Italian Spanish

ArtGraver.com
EngravingForum.com
EngravingLessons.com
AirGraver.com
EngravingSchool.com

HandEngravingClasses.com
EngravingGlossary.com
LindsayEngraving.com
Contact - Email